ATA faults during boot
Hello! I am trying to install Alpine3.17 on my macMini 2012late but cannot see its SSD in the /dev. MacOS worked good just before SSD was erased and Samsung Magician shows up that drive operates normally, but I have noticed relevant faults and errors with dmesg during a booting process from USB dongle.
[ 0.557326] Loading boot drivers: ok.
[ 0.558557] Mounting boot media...
[ 0.581232] libata version 3.00 loaded.
[ 0.582342] ahci 0000:00:1f.2: version 3.0
[ 0.582513] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
[ 0.582516] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 0.590993] scsi host0: ahci
[ 0.591181] scsi host1: ahci
[ 0.591305] scsi host2: ahci
[ 0.591420] scsi host3: ahci
[ 0.591515] scsi host4: ahci
[ 0.591614] scsi host5: ahci
[ 0.591667] ata1: SATA max UDMA/133 abar m2048@0xa0716000 port 0xa0716100 irq 31
[ 0.591673] ata2: SATA max UDMA/133 abar m2048@0xa0716000 port 0xa0716180 irq 31
[ 0.591675] ata3: DUMMY
[ 0.591676] ata4: DUMMY
[ 0.591676] ata5: DUMMY
[ 0.591677] ata6: DUMMY
[ 0.906733] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 0.907171] ata1.00: unexpected _GTF length (8)
[ 0.910063] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.293745] tsc: Refined TSC clocksource calibration: 2294.786 MHz
[ 1.293766] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2113f7e44a7, max_idle_ns: 440795281465 ns
[ 1.293824] clocksource: Switched to clocksource tsc
[ 5.987079] ata1.00: qc timeout (cmd 0x27)
[ 5.989295] ata1.00: failed to read native max address (err_mask=0x4)
[ 5.989307] ata1.00: HPA support seems broken, skipping HPA handling
[ 6.304355] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 6.304914] ata1.00: unexpected _GTF length (8)
[ 6.304928] ata1.00: supports DRM functions and may not be fully accessible
[ 6.304931] ata1.00: ATA-11: Samsung SSD 860 EVO 500GB, RVT02B6Q, max UDMA/133
[ 21.987077] ata1.00: qc timeout (cmd 0x2f)
[ 21.988200] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x4
[ 21.988213] ata1.00: NCQ Send/Recv Log not supported
[ 21.988216] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 21.988222] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x40
[ 21.988225] ata1.00: ATA Identify Device Log not supported
[ 21.988228] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x40
[ 21.988230] ata1.00: ATA Identify Device Log not supported
[ 21.988232] ata1.00: Security Log not supported
[ 21.988243] ata1.00: failed to set xfermode (err_mask=0x40)
[ 21.988249] ata1: limiting SATA link speed to 3.0 Gbps
[ 21.988251] ata1.00: limiting speed to UDMA/133:PIO3
[ 22.301043] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 22.301586] ata1.00: unexpected _GTF length (8)
[ 22.301597] ata1.00: supports DRM functions and may not be fully accessible
[ 37.347077] ata1.00: qc timeout (cmd 0x2f)
[ 37.348200] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x4
[ 37.348214] ata1.00: NCQ Send/Recv Log not supported
[ 37.348218] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x40
[ 37.348221] ata1.00: ATA Identify Device Log not supported
[ 37.348223] ata1.00: Read log 0x00 page 0x00 failed, Emask 0x40
[ 37.348226] ata1.00: ATA Identify Device Log not supported
[ 37.348228] ata1.00: Security Log not supported
[ 37.348245] ata1.00: failed to set xfermode (err_mask=0x40)
[ 37.348249] ata1.00: disabled
[ 37.664404] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 37.668537] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 37.668740] ehci-pci: EHCI PCI platform driver
[ 37.668881] ehci-pci 0000:00:1a.0: EHCI Host Controller